Display
Inputs
Outputs
Modbus
Battery
Cell
Addresses
Calibration
Security
System
Reserved
Date
The system date e.g. for data logging
Time
The system time e.g. for data logging
Backlight
Brightness of the display
Power Save Mode
Time to switch off display
Language
Sets the system language
Disabled
Input 1
Input 2
Input 3
Input 4
Mode
Input function
Disabled
Sensor 50A in
Sensor 100A in
Sensor 200A in
Sensor 400A in
Sensor 600A in
Sensor 50A out
Sensor 100A out
Sensor 200A out 
Sensor 400A out
Sensor 600A out
Isolation Alarm
Inverted
Inverts the function
No
Yes
On/Max
Switch-on threshold in volt
Off/Min
Switch-off threshold in volt
Output 1
Output 2
Output 3
Output 4
Mode
Output function
Disabled
SOC
Cell LVP
Cell OVP
Alarm
Inverted
Inverts the function
No
Yes
On
Switch-on threshold in %
Off
Switch-off threshold in %
GreenView slave address
Slave address for slave connector
Cell type
Please select a suitable cell type from the database 
Capacity
Cell capacity in Ah at I = C/20
Cells
Number of cells
SOC mode
SOC (State Of Charge) is voltage or current based
Voltage
Current
Cell- parameter
To change: select param. and touch on pen
Change paramter...
Password:
VNC-Server
Click on pen to change the password
Reserved
No.
Type
Uchg [mV]
UdisChg [mV]
Ichg [%]
Tchg [Min]
Peukert [1/100]
CEF [%]
LVP Start [mV]
LVP Stop [mV]
OVP Start [mV]
OVP Stop [mV]
LVP Alarm [mV]
OVP Alarm [mV]
Edit parameter (experts only)...
Register value
Real value (with current battery system)
OK
Cancel
Cell chemistry
Cell full detection voltage
Cell empty detection voltage
Cell full detection current
Cell full detection time
Peukert exponent e.g. 125 = 1.25
Charge efficiency factor
Low voltage protection start
Low voltage protection stop
Over voltage protection start
Over voltage protection stop
Low voltage alarm
Over voltage alarm
Pb (2V)
NiCd (1,2V)
NiMH (1,2V)
LiFeYPO4 (3,3V)
LiFePO4 (3,3V)
LiFeMnPO4 (3,2V)
LTO (2,4V) 
Lithium-Ion (3,7V)
Current address
The current address of the device to be configured (factory setting 1)
New address
This address will be programmed to the device. Make sure this address is unique.
Execute!
The new address is set. Devices with the same address must be disconnected or switched off first.
Reboot & Search!
After an address change the device must be restarted. Reconnect all devices before.
Searching device...
Error: No answer from device!
Found Device %s on address %d
Error: Device id unknown!
New address is written.
Input 1
Input 2
Input 3
Input 4
Reading
Current reading
Offset
Zero correction
Gain
Maximum value correction
No saved Configuration
Search Configuration
Search
New
via modbus
Load
Stored
from sd-card
devices
save search data
FAULT restart device
SD-Card:
ISOLATION FAULT SHUTDOWN SYSTEM!!
Insert SD-Card
occured
cleard
ERROR
Device ERROR
Temperature ERROR
load from CONFIG
unknown device type:
Found:
with slave id
timeout
search
found
Reading device data
Saving data
Battery voltage
GreenView         slave address
Disable                  ethernet
Disable ethernet to reduce power consumption, restart device to take effect
Network
voltage divider
Vdiv factor/10
Level
Level IN1
Level IN2
Level IN3
Level IN4
parameters
Exclude this BMS/Cell from#system voltage calculations.
Back
Save
Cannot write configuration data to disk. Error code
WARNING! CHANGE THESE SETTINGS ONLY IF YOU ARE ABSOLUTELY SURE OF WHAT YOU ARE DOING!
List of available parameters
Enable digit#edit
Exclude this device from system#total current calculations.
Battery Voltage ERROR
Battery Current ERROR
ATTENTION!
DISCONNECT EVERYTHING FROM A-CONTACT OF GREENMETER AND KEEP BATTERY CONNECTED TO B-CONTACT. MAKE SURE THAT GREENMETER IS COOLED DOWN TO ROOM TEMPERATURE BEFORE CALIBRATION. REFER TO MANUAL FOR DETAILS.
Continue
Cannot send data to server
Cannot find IP address for server
Cannot create MQTT-subscription to server
Cannot connect to server
Too much difference between battery voltage on GreenController(%d) and overall voltage on BMSs(%d)! %s
Too much difference between battery voltage on GreenController(%d) and overall voltage on BMSs(%d)!
BMS voltage is out off range! Balancing is stopped!
 Message
Restart the device to apply changes!
<Enter host name or IP-address>
Enable MQTT
MQTT server name or#IP-address
Access token
Upload data#to server every
Clear
min
Processing database, please wait...
Rescale, please wait...#